Golf Cart

BEHAVIOR
Carries half of a foursome around 18 holes and to the 19th hole as well. It
provides a speedy and effortless way to play a round of golf.
HABITAT
You find these fun-driving machines on golf courses and in retirement communities, especially in Arizona and California.
HOW IT WORKS
Electric motors or gasoline engines propel this buggy up to 15 miles per hour. Low-pressure tires spread the weight of the cart and cargo so not to damage grass. Even so, it is against the rules to drive on a putting green.
Golf carts have automatic transmissions that change the effective gear ratio from about 3:1 at low speeds to 1:1 at high speeds. The clutch has two parts: one attached to the crankshaft and the other to the shaft that powers the differential and turns the wheels. They are connected by a drive belt. The two clutches change in opposite ways as the engine speeds up. The one attached to the engine forces the belt to ride on a larger diameter shaft, and the one that powers the wheels moves onto a lower diameter shaft. At low engine rpms the engine turns three times for every revolution of the wheels, providing power. At higher engine rpms the engine turns once for each revolution of the wheels to provide speed. This magic is made possible with ingenious centrifugal weights and springs.
Gasoline engine golf carts have governors to limit the speed of the engine. The governor is there to prevent damage to the engine and not to limit your speedy driving. Some carts have a spring device that limits how far the accelerator can be pushed. Others limit the throttle by means of a device connected to the clutch that powers the drive wheels. A third type controls the spark plugs electronically.




  • READ MORE.......






  • A field guide to automotive technology
    Ed Sobey


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---



  • www.automotive-technology-guide.com







  • 7:11:00 AM

    Wiper

    Your windshield wipers suddenly halting or no longer function normally? Let's not let such conditions continue. You see, wipers like that can damage or scratch your windshield. Moreover, if the rubber is contained on your wipers are no longer able to function as a windshield wiper or cleaner perfectly.
    Choked or breakdown of the wiper can be caused by or pivot on the wiper that has been worn or damaged. If you are experiencing it means wipers had to be replaced with new ones. Likewise, if the rubber in your wiper is damaged. You should immediately replace with new ones.
    Before making such changes, should you need to first know what type of wipers. Basically the type of wiper consists of two pieces.
    First, the wiper has a kind of knob lock is red or black plastic. To remove the wiper of this type, press the knob down so you can slide the rubber blade of the clip frame.
    Second is the type of wiper with a more sophisticated model. Wiper This model has a simple lock mechanism. Simple lock mechanism allows the tip of the blade can be curved downward. Up regardless of the grooves that hold the clip from the chassis, so that the blade can be removed and removed from the framework.
    As for replacing the wiper with a new one, do the opposite of how to remove the wiper. If you have wiper has two plastic knob, how to set it up can be done by pressing the knob down so that the new wiper blade rubber you can plug right on the chassis clips.
    Meanwhile, if your wipers are a more sophisticated model, then you must remove the key with arching blade tip down, so that the clip detached from the chassis. After that you can do the installation of a new wiper on the clip.
    If the new wiper installation procedure you have done, the important thing to remember is to always put all the clips contained on the wipers. Whatever kind you use the wipers.

  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 6:13:00 AM

    the Mustang Boss 302

    In 1970, the Mustang Boss 302 was in its second year. Its 302-cubic -inch V-8 used cylinder heads from the 351 Cleveland V-8 and was rated at 290 hp. This pristine example, a numbersmatching car that
    underwent a rotisserie restoration earlier this year, is owned by Mike Friedlander of Ann Arbor, Michigan.


    Given how enthusiastically Ford has mined the Mustang’s rich history, it was only a matter of time before we would see the Boss nameplate again. Well, the time has come: Ford rolled out the new Mustang Boss 302 (for static display only) at the historic races at Mazda Raceway Laguna Seca in California. The car will rumble into dealerships next spring as a 2012 model. The corral of high-performance Mustangs is getting crowded. After all, the Mustang GT is newly fortifi ed with 412 hp from its recently introduced 5.0-liter engine, and the Mustang Shelby GT500 pounds out 550 hp from its supercharged 5.4-liter V-8. So one might reasonably wonder where the Boss 302 fi ts in. The short answer is: between the two, in both price and performance. But the more in-depth answer is that this car isn’t supposed to be merely an intermediate step in a hierarchy of hopped-up Mustangs; it’s actually something racier, more hard-core, and really, really cool.

    Like its 1969 namesake—which was essentially a street version of the SCCA Trans-Am race car—the
    new Boss 302 was designed with an eye toward the track. That’s particularly true of the Boss 302 Laguna
    Seca edition, a limited-production, streetable track version that tosses out the back seats in favor of additional
    body sti eners and features an even more extreme chassis setup.
    Both the standard Boss 302 and the Laguna Seca move the Mustang away from a traditional, Detroitstyle
    muscle car that is focused on 0-to-60-mph performance fi rst and handling second. Instead, the dictum
    with the Boss was to create “the best-handling Mustang ever.” Mustang engineers also aimed to increase
    power output not with a heavy—though e ective— supercharger, but instead by getting the 5.0-liter
    V-8 to rev more freely. They also wanted to give it more power in the upper rev ranges, consistent with how the Boss will likely be used on a track.
    Thus, changes to the 5.0-liter V-8 were not just to increase its output but also to alter its nature. Not surprisingly, the modifi cations are extensive. There’s a new intake manifold and ported cylinder heads for
    better breathing. An engine oil cooler, a lighterweight valvetrain, forged (rather than cast) aluminum pistons, and forged connecting rods are designed to handle higher engine speeds. Ford engineers used the Boss 302R
    racing car as a development test bed, and, based on their experience at the track, they revised the road car’s radiator to improve engine cooling and added ba es to the oil pan to prevent oil starvation.
    The net result of all these changes is an engine redline that has been raised by 500 rpm to 7500 rpm and an increase in power output from 412 hp to 440 hp at 7500 rpm—at a cost of 10 lb-ft of peak torque, with the Boss 302’s V-8 rated at 380 lb-ft at 4500 rpm.
    One of the more interesting aspects of the Boss engine is its exhaust system. Supplementing the standard Mustang GT’s dual exhausts are two additional pipes that exit just ahead of the rear wheels. These side exhaust outlets incorporate metal discs that keep the sound at legal levels— but they are removable, should the owner want something louder. The Boss is plenty vocal even with the discs in place, as the induction
    sound tube has been retuned and eleven pounds of sound deadening have been stripped out.
    The engine sends power rearward via an upgraded clutch with a steel-backed disc and a short-throw, close-ratio sixspeed manual (no automatic is available).
    Whereas the Mustang GT has a 3.31:1 fi - nal-drive ratio, the Boss gets a 3.73:1 unit, with carbon-fi ber friction plates in its limited slip; a Torsen rear axle is standard on the Laguna Seca model and is optional
    (bundled with Recaro seats) on the regular Boss 302.
    Any car expecting to see racetrack duty needs serious brakes, and so the Boss upgrades from the Mustang GT’s 13.2-inch front discs to the GT500’s fourteen-inch vented front discs and four-piston Brembo
    calipers. The GT’s standard 11.8-inch rear rotors are retained, but the pad material is upgraded. Brake lines have been sti ened to improve pedal feel. The Laguna Seca additionally receives front brake-cooling
    ducts—they’re available as an accessory for the standard Boss 302.
    As expected, the Boss features fi rmer springs, antiroll bars, and suspension bushings, but the car takes the driver-tunable racing aspect one step further with manually adjustable front and rear dampers. The
    fronts are accessible from under the hood  and the rears from in the trunk; drivers can use a screwdriver to select one of fi ve sti - ness settings. Position 1 is equivalent to a GT with the Brembo brake package, while
    positions 2 through 5 are progressively sti er. The Laguna Seca’s softest setting (1) matches the Boss 302’s fi rmest setting (5). The steering e ort is also driver-adjustable. Electric power steering was introduced
    with the 2011 model year, and as in the Mustang GT, drivers can choose among three e ort levels. Similarly, the traction and stability control systems include a competition mode that allows greater drift
    angles, or they can be shut o entirely. The tire and wheel package consists of nineteen-inch aluminum alloys for both cars. The Boss 302 wheels, painted black, are nine inches wide in the front and 9.5 inches in the rear and are wrapped in Pirelli PZero rubber; the Laguna Seca wheels are another half-inch wider in back, are fi nished in orange and silver, and use R-compound PZeros.
    Ford likes to say that the Boss isn’t just a sticker-and-wheel package. True enough, but that doesn’t mean that exterior graphics have been ignored. Indeed, the huge C-stripe on the side is an unmistakable homage to the original 1969 Boss. The stripe color (black or white) is repeated on the hood and the roof. Additional exterior design elements include a front splitter, a rear wing, and a grille with blanked-out foglight holes (why not just design a newgrille?). Body colors are red, blue, orange, yellow, or white. The Laguna Seca gets red
    graphics, with additional color splashes on the grille surround and mirror caps. Its base body colors are black or silver only. It also has more extreme aero aids, taken directly from the 302R racing car.



  • READ MORE.......



  • (Automobile Magazine)
    storemags & fantamag - magazines for all


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com




  • 8:24:00 AM

    HTML5 and the software engineer

    HTML5 appears to have a number of benefits for consumers and car manufacturers. But what is often good for the goose is not necessarily good for the developer. Talking to the guys in the trenches is critical to understanding the true viability of HTML5.

    Andy Gryc and Sheridan Ethier, manager of the automotive development team at QNX, pair up for a technical discussion on HTML5. They explore whether this new technology can support rich user interfaces, how HTML5 apps can be blended with apps written in OpenGL, and if interprocess communication can be implemented between native and web-based applications.

    So without further ado, here’s the latest in the educational series of HTML5 videos from QNX.



    This interview of Sheridan Ethier is the third in a series from QNX on HTML5.

    Check V-Belt Components

    Components of this one made ​​of rubber material. The shape is round with a length as needed. His job is vital, such as turning the alternator, engine cooling systems and air conditioning systems (AC). But if to break up, guaranteed to bother the driver.

    Prior to the things that are not desirable, how to detect it quite easily. First, check the estrangement by using index finger. Then press with little effort. If it comes a bit loose, should be aware.

    Then check the condition of V-belt itself. If the conditions encountered torn or cracked, you should immediately
    be replaced. Or follow the instructions in accordance with the vehicle inspection book.

    However, it is advisable to bring a spare V-belt on every car. Especially for vehicles that are often taken long trips. So, if at any time there is damage, it can be replaced immediately.


  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 7:19:00 AM

    Choosing the right tires for your car

    Hope all of you had a wonderful Christmas. I had a great time with family and few friends in London. While chatting with the guys about cars I realised that most of us had only one set of tires (or Tyres for those in the UK) which we only changed when they were worn out.

    Like most people, I leave it up to the tire shops to recommend and change the tires. However, there are a range of tires to choose from but it is important to be aware that all cars have different requirements depending on the type of car and what you usually use it for. For example it would not make sense to have performance tyres usually used for racing for your family car which you normally use for every day commuting.

    Moreover now that winter is here, it is a good idea to think about winter tires as well. The winters here are not that bad and so far we have had fairly great weather without any snow, we never know. It was fairly bad last year and I had a tough time driving in the snow using my normal tires. I have learnt my lesson and have got myself some winter tires which I ready to change to once it starts snowing.

    Anyway, if you are interested in learning more about the different styles of Car Tires, check out Tires information site.

    Amphicar and Aquada

    BEHAVIOR
    It’s a car. It’s a boat. No, it’s both! It drives on land and water.
    HABITAT
    Mostly found now in Amphicar shows or rallies organized by enthusiasts, you rarely get to see them on the road.
    HOW IT WORKS
    A 43 HP Triumph motor powers both the wheels and two small propellers that protrude from the rear end. This rearmounted motor gives the amphibious car a top land speed of 70 mph and top water speed of 8 mph. It has no rudder and steers by the driver turning the front wheels.
    The car is watertight so the occupants and their luggage are kept dry. But just in case, it does have a bilge pump. As a motorized boat  and car, an Amphicar needs to be licensed for both. Not practical for most driving or boating applications, but in some cases it is an ideal compromise vehicle. Fewer than 4,000 were ever produced, all between 1962 and 1967 in Berlin.
    Amphicars made some significant ocean crossings: from Africa to Europe and from England to France. The Amphicar was not the first automotive amphibian and not the last. Very recently a UK company has developed high speed amphibious technology and is selling amphibious cars called Aquada.
    Instead of propellers, the Aquada uses a water jet for propulsion. An engine spins impeller blades that accelerate water and push it out the rear of the car/boat. Steering is accomplished through a nozzle that can
    swivel. To go in reverse, the impeller spins in the opposite direction. Besides going much faster across the lake than an Amphicar (as fast as 30 mph), the water jet is safer since it has no external blades that spin.
    The Aquada also has retractable wheels to reduce the water drag.
    Pushing one button retracts the wheels and disconnects them from the engine. When you come to the shore, drop the wheels and drive home. If you buy one, please give me a ride.
    INTERESTING FACTS
    Purchased new from 1962 and 1967, Amphicars cost less than $3,500. In 2006 a used Amphicar was sold for over $100,000.


  • READ MORE.......


  • A field guide to automotive technology
    Ed Sobey


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 7:21:00 AM

    Tips to minimize fuel consumption

    Fuel price increase will certainly impact on the increasing number of costs to drive. These are some tips to minimize fuel consumption while driving a car.
    • In manual transmission, the amount of fuel flowing from fuel tank to the engine is a function of stamping on the accelerator pedal (gas pedal). Getting stepped on, the faster the flow of fuel to the engine. To minimize fuel consumption, we need as much as possible to minimize the stamping on the accelerator pedal / gas.
    • When picking up speed in the car with manual transmission, replace the transmission quickly. Or in other words, use the transmission as high as possible but still keep the power from the engine. If the higher transmission requires a stamping on the gas pedal a little more, then change to a higher transmission. The opposite is also true, if a lower transmission requires a stamping on the accelerator a little more, then change to a lower transmission, this applies especially if the road or climb under the car was carrying a heavy load.
    • Minimize the brake pedal. The use of brakes will convert kinetic energy into heat energy in the brake disc. While the previous car's kinetic energy comes from chemical energy contained in gasoline. For example, if your car drove into an intersection, you should refrain from pressing the gas pedal long before the close to the intersection, move the transmission into neutral and just put the brakes on a car near the intersection after. If you choose to keep improving acceleration, the fuel is wasted into heat will be more.
    • When buying a car, choose the automatic transmission cars. Automatic transmission car should be easier to use if we want to save fuel without the need to change your driving habits. Whether or not wasteful fuel consumption on manual transmission cars more discipline depends on the driver.
    • When buying a car, choose a light-colored car. Dark-colored car will absorb more wavelengths than light-colored car. This will cause the thermal energy more easily into the dark interior. As a result, dark-colored car air conditioner will work harder to mempernyaman car interiors, either automatically or manually by the driver.
    • Avoid traffic jams. Congestion is one of the major sources of waste fuel. If you need to come home from work when the roads were not jammed, or rather take the detour to avoid congestion points. Better yet, use public transportation if possible.
    • Park the car in the shade. Or if it can not find the shade, use light reflectors to minimize the heat energy into the car. A hot car interior will make the AC work harder, especially when the new start the car.
    • Choose a car with engine size and low number of cylinders. Engine capacity and number of cylinders is not too important. 4-cylinder engine vehicles with 1.3 liter capacity each function with a 6-cylinder car engine capacity of 3 liters. Both can bring yourself to your destination. The biggest difference is that large automobile engines are generally more intensive than gasoline engines small cars.
    • If buying a car, choose a new car with the latest technology. The new engine technology is usually more efficient than gasoline cars with old technology.
    • Do not be late for an oil change. The longer the use of oil, then power pelumasannya will be minor. As a result, more fuel is converted into heat inside the machine.
    • If the later is available in Indonesia, choose a hybrid car. Like conventional cars, hybrid cars have an internal combustion engine. But, in addition, hybrid cars also have a battery and electric engine. Hybrid cars save energy by converting some waste heat energy into electrical energy that can later be used to run the car.
    • Use a proven car fuel efficient. In other words, use the Honda City or Jazz.


  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com



  • 5:04:00 AM

    Integration of materials into designs

    General
    The above appraisal of designs shows how the choice of material is paramount to achieving today’s objectives and how this choice is widening. Having minimized the weight of a specific design and assuming the best materials have been specified, the next consideration is to optimize material with regard to each link in the chain of processing operations necessary to produce a functional part, and as will be  described in Chapter 4 each of these elements can strongly influence the selection. For instance, complex parts require maximum formability which requires a compromise with strength, realistically placing a maximum at around 300 N/mm2 proof stress, although for simple sections such as door reinforcement beams levels of 1200 N/mm2 may be specified. The constraints imposed by local steelmakers may obviate certain grades
    where for instance a bake-hardening or isotropic steel is required, and a restricted choice of coating types may be available. However, despite these minor restrictions apart from obvious exceptions most  manufacturers are maintaining a conservative steel grade policy, requiring only minimal changes in processes, and as has been seen above the use of predominantly aluminium structures is only evident by one or two
    of the more adventurous companies who can absorb the extra supply and manufacturing costs. The majority would still prefer the more cautious approach employing the advantages of aluminium for closure or ‘bolt-on’ parts and using the accompanying weight savings to satisfy legislative weight-band requirements or added sports car performance. Many manufacturers are, however, gaining valuable manufacturing experience by building low volume sports models in aluminium, e.g. NSX or BMW Z8 or specific parts Peugeot 607. Once the different disciplines demanded by this less robust material are fully understood and a way is found of absorbing the extra cost it may then find a wider usage. Plastics as referred to later in this section require
    much development in an engineering context and only very expensive derivatives fulfil impact and other functional requirements. Until the market price falls then use will be limited to exterior cladding and trim items. Thus, for the main body structure the increasing use of high strength steel will continue to develop and the trend for a typically progressive European car manufacturer such as BMW is shown in Fig. 2.14 – a weight saving of 10–15 per cent being achieved for selective parts via thickness  reduction. Magnesium is now starting to find favour as the quest for lower density materials intensifies, but has been used occasionally in the past, e.g. Austin Maestro gear box covers. The latest interest is for vehicle cross-beams and similar aluminium products as described in the following sections.




  • READ MORE.......



  • Materials for Automobile Bodies
    Geoff Davies F.I.M., M.Sc. (Oxon)
    AMSTERDAM BOSTON HEIDELBERG LONDON NEW YORK OXFORD
    PARIS SAN DIEGO SAN FRANCISCO SINGAPORE SYDNEY TOKYO


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---


  • www.automotive-technology-guide.com




  • 5:46:00 PM

    Tubeless tires

    Today, almost all types of sedan vehicles using the ordinary kind and radial tires are tubeless (without inner tube). If punctured a nail or other sharp objects, tubeless tires will run out the wind. It is obviously very dangerous in addition to make you upset.

    If a flat tire, which take into account is the source of the leak. Unplug the nail or other object that caused the leak. Clean the dirt that is until it is completely clean. Next, remove the remaining air inside the tire until completely dry.

    Next, using a spiral screwdriver, find the direction of the hole carefully so as not to create new holes. Screwdriver spiral rotated to the right until a maximum, then pull back the screwdriver to the right as well. Glue or glue chemical vulcanizing fluid Castol on spiral and stick a screwdriver into the hole. Repeat the job twice and set aside some time.

    Next take the needle clamp and permacure parts used to clog the hole. Open the wrapper and label glue permacure taste. Place the needle in the middle permacure. Unplug the spiral screwdriver inserted in the hole and carefully stick flops and permacure needle toward the hole as deep as possible. Then unplug immediately. If a large hole, use some permacure.

    To smooth the remaining permacure use a knife and wait a while until the glue dried. After that the tire can be pumped as needed.



  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 7:44:00 AM

    CONCEPT OF HYBRID VEHICLE DRIVETRAIN

    Any vehicle powertrain is basically required to (1) develop sufficient power to meet the demands of vehicle performance, (2) carry sufficient energy on-board to support vehicle driving in the given range, (3) demonstrate high efficiency, and (4) emit less environmental
    pollutants. Broadly, a vehicle may have more than one energy source and energy converter (power source), such as gasoline (diesel)-IC engine system, hydrogen-fuel cell-electric motor system, and chemical battery-electric motor system. A hybrid vehicle drivetrain consists of two power sources. One is the primary power source and the other is secondary
    power. For the purpose of recapturing part of the braking energy, hybrid drivetrain has at least one bidirectional energy source, typically chemical battery-electric motor system. At present, IC engines are the first selection for the primary power source, and perhaps fuel cells in the future.
    Architecture of a hybrid vehicle is loosely defined as the connection between the components that define the energy flow routes and control ports. Traditionally, HEVs were classified into two basic types: series and parallel. It is interesting to note that, in 2000, some newly introduced HEVs could not be classified into these kinds [5]; hereby, HEVs are newly classified into four kinds: series hybrid, parallel hybrid, series-parallel hybrid, and complex hybrid, which are functionally shown in Figure 3.1 [4]. In Figure 3.1, a fuel tank-IC engine and a battery-electric motor are taken as the examples of the primary power source (steady power source) and secondary power source (dynamic power source), respectively. Of course, the IC engine can be replaced by other types of power sources, such as fuel cells. Similarly, the batteries can be replaced by ultracapacitors, flywheels, or their combinations.



  • READ MORE.......



  • Handbook of Automotive Power
    Electronics and Motor Drives
    Edited by
    Ali Emadi
    Illinois Institute of Technology
    Chicago, Illinois, U.S.A.
    Boca Raton London New York Singapore
    A CRC title, part of the Taylor & Francis imprint, a member of the
    Taylor & Francis Group, the academic division of T&F Informa plc.




    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---


  • www.automotive-technology-guide.com




  • 8:01:00 AM

    The connecting rod

    Typical connecting rods are shown in Figs 9.1 and 9.2. The connecting rod is generally abbreviated to con-rod. The crankshaft con-rod mechanism transforms reciprocative motion to rotational motion. The con-rod connects the piston to the crankshaft to transfer combustion pressure to the crankpin. There are bearing portions at both ends, the piston side is called the small end, and the crankshaft side, the big end.
    The con-rod must withstand very high forces as the piston moves within the cylinder bore. The shaft portion of the con-rod is subjected to bending as well as tension and compression. The bearing portions receive load from the weight of the piston and the con-rod. To avoid failure of the bearings, the con-rod should be made as light as possible. To avoid buckling, the rod portion usually has an I-beam shape because of the high rigidity-to-weight ratio of this shape. Figure 9.3 shows the cross-section.
    Although con-rods for both four-stroke and two-stroke engines have an Ibeam
    shape, the thickness distribution is slightly different in the two engines. The four-stroke con-rod receives a large tensile load during the exhaust stroke as well as a compressive load during the combustion stroke. The inertial force of the reciprocating mass generates a tensile load which is proportional to the product of the piston assembly weight, reciprocating mass of the con-rod and square of the rotational velocity. It is bigger than the compressive load above a certain rotational speed.



  • READ MORE.......


  • The science and
    technology of
    materials in
    automotive
    engines
    Hiroshi Yamagata
    Woodhead Publishing and Maney Publishing
    on behalf of
    The Institute of Materials, Minerals & Mining
    CRC Press
    Boca Raton Boston New York Washington, DC
    WOODHEAD PUBLISHING LIMITED
    Cambridge England


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com

  • 9:20:00 AM

    Plugs car started weak

    When we start weak car spark plugs, ignition process in the engine and the car will be running a car crashed into halting. The car that has a spark that was old and weak are usually not easily in starter in the morning and was not powered while driving. Fuel consumption will be higher if the condition of the spark plug is too old. Most spark plugs require replacement every 15 thousand miles or about 24 thousand km.
    But usually on new cars that have platinum spark plugs only need to be replaced every 60 thousand miles or about 96 km. If you have an old car, this article will provide input on how to replace your spark plugs properly.
    The workings of the two cable plugs are located very close together, making it possible to trigger a spark. Distributor of car engines will continue the flow of electricity that flows through the ceramic casing lining the wire from the spark plug and the other jumped into a grounded wire, to meet the circuit and then start the engine.
    When the spark plug was crusty, the electricity would not be a success and will lead to a shortage of cars. This reduction in force will cause some problems with your vehicle, such as the vehicle crashed, halting way, hard in starter and fuel consumption was normal.
    To replace the old spark plugs, your vehicle's engine must be cooled first. If your vehicle wears out, wait for approximately two hours after the trip, to make sure it is really cold. To prevent further damage, off your car battery.
    Clean the inside of the spark plugs by using a blower. You can use a tire pump or air compressor to clean each cavity to clean dirt, dust or crust. Cleaning the crust by using a blast of air is so important that when the spark plug removed no one falls into the cylinder.
    Remove the spark plug wire by turning the rubber cap while pulling. Do not immediately pull the spark plug wires, because it could ruin it. open spark plug from its socket. Spark plug sockets have a rubber coating that will prevent damage to the ceramic casing. Remove the spark plug from the socket by turning it.
    Be careful, do not drop anything onto the engine cylinder, piston or head.


    Serious damage to the cylinder or head will occur if any foreign object attached to it. New spark plugs in accordance with the specifications of your vehicle's engine must be available. When installing new spark plugs, you should lubricate each spark plug as a treatment step. This will help to further facilitate the replacement of spark plugs.
    Required the ability to be able to distinguish each spark plug according to specifications from the manufacturer. You can buy the plugs that match your vehicle at a store that provides genuine spare parts of your vehicle. Install each spark plug in each cylinder on your machine.
    Tightly secure new spark plugs, spark plugs you have installed it by using your hands, then by using a key size of a spark plug with spark plugs that you plug it. Install each spark-plug wires on the spark plugs. And then not to forget to change it back after your vehicle mileage has been given above



  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com

  • 9:01:00 AM

    Is HTML5 a good gamble?

    As the consumer and automotive worlds continue to collide, HTML5 looks like a good bet. And not a long shot either. In fact, the odds are all automakers will eventually use it. But since the standard won’t be mature for some time yet, should you take a chance on it now? 

    To answer this, Andy Gryc talks to Matthew Staikos of RIM. Matthew is the manager of the browser and web platform group at RIM, and has over 10 years of software development experience with a strong focus on WebKit for mobile and embedded systems. Matthew co-founded Torch Mobile, which was acquired by RIM for their browser technology.

    Andy’s conversation with Matthew is the subject of the following video, the second in an educational series designed to get an industry-wide perspective on HTML5. 




    This interview of Matthew Staikos is the second in a series from QNX on HTML5.

    Scion tC

    Strong enough for a man, but made for a young woman.

    SAN DIEGO
    HE tC IS SCION’S biggest success. Yes, it’s the brand’s all-time best-selling model, but that’s only half the story. If you remember, the whole point of Scion was to lure younger buyers to Toyota—and the tC’s buyer is the youngest in the industry. At twentyfour years old, he’s about half the age of the average new-car buyer.
    Or should we say, “she”? You see, even though the tC initially appealed to male enthusiasts, its buyers gradually skewed female, and the take rate for the manual transmission dropped steadily. So what? A buyer is a buyer, right? Not so, say the marketing folks. As it turns out, you can design a car for guys, and girls will likely buy it, too. But if a model is branded a “chick car”? Well, guys will run in the other direction.
    For its second-generation tC, Scion wants to get the stick-shift-buying enthusiast dudes back into the dealerships. And to do that, it put its sport coupe on an emergency lesstrogen program. With styling cues taken from the hypermasculine Fuse Coupe Concept unveiled at the 2006 New York auto show, the 2011 tC looks decidedly less cute and more aggressive.
    It remains instantly recognizable as a tC, which is a good thing, because it
    means that Scion learned its lesson from the xB, which alienated its young buyers
    when it grew substantially for its second generation. The new tC matches its
    predecessor in every exterior measurement except width, which has grown by a substantial 1.6 inches. No one ever complains about a sporty car being too wide—and the increased track (up 1.3 inches in front and 2.1 inches at the rear) helps give this tC a more substantial presence.
    Standard eighteen-inch wheels don’t hurt, either.
    The increased width also helps the interior feel more spacious. The contoured seats are still supportive but are an inch wider than before. A glass dual sunroof is
    standard, and—with the exception of a red LED clock that looks straight out of the 1980s—the cabin is modern and attractive.
    Unfortunately, the dashboard is a mishmash of hard plastics with three completely di erent grains, and the center armrest is rock hard. The steering wheel, on the other hand, now telescopes in addition to tilting and is a delightfully thick, leather-wrapped, fl at-bottomed a air with standard audio controls. It’s easily the highlight of the interior and is enough to make up for a multitude of material sins.



    (Automobile Magazine)
    storemags & fantamag - magazines for all

    6:20:00 AM

    the engine is not strong at-starter

    There is one problem that is often experienced by motorists. Ie: the engine is not strong at-starter. When the ignition key in START `position`, the machine would not turn. Only the sound of `tek ... `tek. As a result, the car was not able to walk.

    Based on data from Emergency Roadside Assistance (ERA) AstraWorld, this is indeed the most frequent problems arise. `On average, every month, 30 percent of one thousand units over the ERA is handled this problem,` said Suwarno, Technical and Training Development staff ERA AstraWorld.

    Machines that are not strong starter may occur due to battery or battery not save stun or electric current. Why no stun? Typically, the main cause is lack of water stun empty battery. That is, the amount or quantity of battery acid is not as it should be: not a line between low-level and upper level usually indicated on the battery box.

    Properly controlled quantity of battery acid. When positioned immediately below the low-level add. Because, battery acid works to help cool the battery cells. Tasks that make battery acid is reduced (evaporates when absorbing heat).

    Well, if the water is reduced and the battery is not immediately added, would make the cells inside the curved battery - should these cells are parallel and perpendicular. The curvature of these cells can make a positive and negative plates in contact, which ultimately makes surge. Surge that makes the battery is not able to save the stun.

    The other side to check is the battery terminals. Check whether there is corrosion or not. See also wires the positive and negative. Maybe lax or loose. Corrosion and loose wires to make a weak electric current conductivity. Thus, the current flowing to the starter motor is small and not strong enough to rotate the engine.

    If the battery water is replenished, corrosion cleaned and tightened the cable but still did not want to be a starter, try the battery jumper ``, or `fished`. You do this by connecting the car battery is not strong starter with another car. Of course, battery capacity must match the two cars. Maybe it's a bit difficult to do because in addition to need another car, also need to jumper cables.

    Especially for a car with gears (transmission) manual no alternative. You can trigger the spin machine to propel the vehicle. Try to turn the ignition on position `ON`. Enter the second gear, then stepped on the clutch pedal, then push the car. Once the car reaches a speed of rotation of the tire enough, lepaslah clutch pedal. Properly, so the pedal is released, the engine to life. This too may be a bit difficult because it takes help from others.

    If the steps above have been done but the problem remains unsolved, you need not worry. `Call it AstraWorld ERA. Service Agent we will immediately go to the place you're having trouble, 'said Suwarno.

    To prevent the engine starter is not strong, according to Suwarno, do routine maintenance on your vehicle battery. As already described above, there are some things that need to be done:

    Check the battery water periodically.

    Check the battery terminals.

    Check the battery cables.

  • READ MORE.......


  • translate fr (astraworld)


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 8:01:00 AM

    Eliminate dew glass when rain

    For car with air conditioning (AC), the dew which often interfere with vision glass inside were easily expelled.
    Stay operate only air-conditioning systems, and all the fog was going to disappear instantly. However, when the air conditioning system was not working normally, is a bit troublesome.
    Rubbing the inside of the glass with a chamois cloth is wet, it can help to dispel the view that the barrier. However, it is also a bit troublesome as well.
    But, you do not need to upset first. Apparently, hair shampoo can be used also to rebuke moisture barrier this view.
    How, apply a little shampoo on the inside of your windshield evenly, but a thin layer only.
    This method is guaranteed to make clear the windshield of your car and do not need to wipe over and over again.
    Because of that, there's nothing wrong if you always set up a small bottle of shampoo on the inside of the car when driving in rainy season or out of town.
    Else if unwilling operated windshield wiper. For this business, you can take advantage of tobacco cigarettes or other tobacco types.
    How, apply this tobacco on the outside of the windshield. It is rather strange, but efficacious been tested.


  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com





  • 4:39:00 AM

    Trying to blow up the XJ Sentinel

    Targeted at the rich, famous and powerful, the XJ Sentinel from Jaguar provides discreet armoured protection. According to Jaguar, they have put through extensive independent testing and certification to the latest national and international standards by QinetiQ®.

    The cars offer ballistic protection up to B7 level (BS EN 1522 level FB7 and BS EN 1063 BR7-), blast protection against 15kg TNT equivalent detonated within close proximity of the vehicle, and substantial under floor grenade protection.

    They are also available with several optional features and can be tailored to individual requirements.

    Turbine and compressor designs

    Figure 11.2 shows a cutaway of a turbocharger. Turbochargers consist of an exhaust gas-driven turbine and a radial air compressor mounted at opposite ends of a common shaft (Fig. 11.3) and enclosed in cast housings. The shaft itself is enclosed and supported by the center housing, to which the compressor and turbine housings are attached. The turbine section is composed of a cast turbine wheel, a wheel heat shroud and a turbine housing, with the inlet on the outer surface of the turbine housing. It  functions as a centripetal, radialor mixed-inflow device in which exhaust gas flows inward, past the wheel blades, and exits at the center of the housing. The expanded engine exhaust gas is directed through the exhaust manifold into the turbine housing. The exhaust gas pressure and the heat energy extracted from the gas cause the turbine wheel to rotate, which drives the compressor wheel. The Ni-based super alloy Inconel 713C (see Table 11.1) is widely used for the turbine wheel.4 A typical microstructure is shown in Fig. 11.4. GMR235, which reduces costs by increasing the iron content, is also used. For much higher temperatures, Mar-M247 is used. The response and combustion efficiency of the wheel in acceleration is related to the inertial moment, a function of the weight. The lower the weight, the lower the inertial moment  and therefore the faster the response. Ceramic wheels5 have been developed, but low toughness means that the blades must be thick, making it less easy to adjust the weight. A wheel made from the intermetallic compound TiAl by investment casting has been marketed.6 It has a specific gravity of 3.9 g/cm3, which is much lower than ordinary titanium alloy, and a tensile strength as high as 600 MPa at 700 °C.
    The compressor section is composed of a cast compressor wheel, a backplate and a compressor housing, with the inlet at the center of the compressor housing. It is a centrifugal or radial-outflow device, in that the air flows outward, past the wheel blades, and exits at the outer edge of the housing. The rotating compressor wheel draws ambient air through the engine’s air filtration system. The blades accelerate and expel the air into the compressor housing, where it is compressed and directed to the engine intake manifold through ducting. The compressor wheel does not have such a high heat resistance requirement, so a cast aluminum wheel (C355) is widely used. A cast Ti-6Al-4V alloy is also used for heavy-duty commercial diesels.


  • READ MORE.......


  • The science and technology of materials in automotive engines
    Hiroshi Yamagata
    Woodhead Publishing and Maney Publishing
    on behalf of
    The Institute of Materials, Minerals & Mining
    CRC Press
    Boca Raton Boston New York Washington, DC
    WOODHEAD PUBLISHING LIMITED
    Cambridge England


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 8:18:00 AM

    Using dimmer and horn

    Polite traffic in our country had been so long since we forget. Understandably, to obtain a driver's license (SIM) in this country, its size is not a skill to bring a motor vehicle. Origin have ID cards and money, guaranteed to get a card that is often referred to earlier times rebues it. Let alone how to drive properly, use dim lights and horn are many drivers who do not understand procedures. Can not believe? Observe the habits of the driver's course at the Toll Road or Toll Jagorawi Cikampek Jakarta. Perhaps, a hundred drivers that exist, there is only no more than 5 people who actually deserve the SIM.
    According to traffic regulations in the international world, which is also contained in Law Number 14 year 1992 regarding the following traffic regulations that accompany it, the horn and dimmer should only be used when an emergency only. Properly, you should immediately turn off or dim lights remotely when you are at the first opportunity passed by other riders from the front.
    When other drivers using dimmer-kedim flashing, that means he gives priority to you to move first. However, this sign is sometimes the opposite effect in our country. This is misguided.
    When you follow another vehicle behind him, was not allowed to turn on the lights dim. Because, in this way can be dazzling vehicle that we follow, and of course very dangerous. Conversely, if we know the other vehicle followed behind who want to precede, while the left lane allows it to be used, preferably a vehicle that immediately precedes it wanted a chance to overtake. However, if heavy traffic, keep track of your path through the Switch, it is allowed, but must be done after the track is completely safe.
    Only problem, the correct way traffic, it has become a rare commodity in this country. When someone wants to drive the right, the e ... can even ridicule. A reckless, even got a cheer. However, there is no harm in politely cultural traffic began to develop as we grow again. Remember! Better a little late origin survived.


  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 2:44:00 PM

    BMW M5 to be launched in Canada in 2012

    updated: 17th Dec 2011

    Another North American BMW news:

    Just found out from the BMW Canada website that the new BMW M5 will be launched there in 2012. The car is the latest update - the 5th generation of one of the most popular sport sedans in the World (BMW claims it to be the most "most successful high-performance sedan in the premium segment of the executive class").

    The new BMW M5 is powered by a eight–cylinder V8 engine with M TwinPower Turbo technology developing 412 kW/560 hp, which can take the car from 0–62mph in 4.4 seconds,

    The engine is mated with a seven-speed M Double Clutch Transmission with Drivelogic, and Active M Differential.

    Exterior details including twin dual–tailpipes and subtle M shaped rear spoiler.

    Check out the clip of six lucky guys who get the change to test drive the car at the Nordschleife, Nürburgring.



    Click the link for more news about BMW Canada

    BMW i3 and i8 at LA show

    BMW recently showed of their i3 and i8 Concepts at the 2011 LA Auto Show.

    Both the i3 and i8 cars are part of BMW's "Project i" and is a separate brand.

    First unveiled at 2011 Frankfurt Motor Show, the i3 is expected to go into mass production in 2013 and available for delivery by the end of the year. The car will be BMW's first zero emissions mass produced vehicle.

    On the other hand, first announced in 2010 and also unveiled at the 2011 Frankfurt Motor Show, the BMW i8 is a hybrid and sporty looking car. The car will be available in 2014. SO far no news on expected prices as yet.

    Night Driving Instructions

    Driving at night is sometimes more fun. The air is not hot, and usually the traffic situation is more swing than during the day. However, this work is sometimes dangerous that you need much more careful. Here are some hints that you should look, for your own safety and other motorists.
    1. To note is that you must see and be seen clearly. Convince, lights, your car's rearview mirror berdungsi well and is clean.
    2. When driving at night, always use big lights and do not get used to use a small light when darkness fell. To be more secure, use a nail markings (delineator) and markers guide (guide post) as a reference in driving.
    3. You can see better with the high beam up to 100 m visibility. However, keep in order not to dazzle other people who come from opposite directions. If you ignore, distant car headlights can dazzle other motorists you to lose control. Not only other people who can hurt, it could be going to hurt yourself. But, if you use a lamp short, do not drive your car more than 65km/jam. Notice that!
    4. Above all else, if sleepy immediately stop your car. A short break, popping out of the car is a powerful way drive drowsy.
    OK.....Hopefully survived until the goal


  • READ MORE.......



  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 7:00:00 AM

    What’s HTML5 got to do with automotive?

    There’s been a lot of noise lately about HTML5. A September 2011 report by binvisions shows that search engines and social media web sites are leading the way toward adoption: Google, Facebook, YouTube, Wikipedia, Twitter, and plenty more have already transitioned to HTML5. Some are taking it even further: Facebook has an HTML5 Resource Center for developers and the Financial Times has a mobile HTML5 version of their website.

    It won’t be long before HTML5 is ubiquitous. We think automakers should (and will) use it. 

    To elucidate the technology and its relevance, we’ve created a series of educational videos on the topic. Here is the first in that series. Interviews with partners, customers, and industry gurus will soon follow. 



    This simple overview is the first in a series from QNX on HTML5. (Personally I like the ending the best.)

    MISSION: NOT AT ALL IMPOSSIBLE - Move over Civic and Corolla.

    The import brands—especially Honda and Toyota—have done an  excellent job providing small-car buyers with good basic transportation. Now it’s Chevy’s turn to prove that there is life beyond Civics and Corollas. The new Chevy Cruze is the small car with greater aspirations.
    The Cruze delivers the essentials—an attractive price, low operating costs, and impeccable durability—with attributes that both the Civic and the Corolla lack.
    • So much extra interior and trunk room that the EPA lists the Cruze in its mid-size category.
    • Ten air bags, antilock brakes, and StabiliTrak stability control are all standard for maximum safety.
    • Standard OnStar and XM radio with trial subscription.
    • Exceptional highway fuel economy, plus a special Eco model that gets 40 mpg on the highway.
    • A wealth of options such as DVD navigation, leather trim, a Pioneer nine-speaker sound system, Bluetooth
    connectivity, a handy USB audio interface port, ultrasonic parking assist, and 18-inch aluminum wheels.
    Chevrolet’s confi dence in the Cruze rests on the fact that more than 330,000 of them are already on the road
    in 60 countries. Prior to its U.S. introduction, the Cruze will have logged more than 4 million test miles.
    With the goal of providing the compact class’s smoothest, quietest ride, 30 acoustical treatments were developed, including body cavities fi lled with sound-absorbing foam, a fi ve-layer headliner, and reinforced door structures. Limiting the gaps between exterior panels to less than an eighth of an inch yields a long-lasting, top-quality appearance.
    The Cruze’s claim to fame will be providing superior value as the best compact car not much money can buy.


  • READ MORE.......


  • (Automobile Magazine)
    storemags & fantamag - magazines for all

    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com



  • 6:29:00 AM

    As caring Wheel Drive FWD Cars

    Plurality sedan type passenger car, always use a front-wheel drive system. Understandably, this method does have many advantages over conventional methods that use rear-wheel drive. Besides being able to reduce the effects of oversteering, FWD cars that use the system is also much simpler construction. You see, transmission and gardannya can be made into a unity so great savings.
    Just persoalnya, shaft or front-wheel drive as this is often problematic. Because the center pedestal and wheel rotation is indeed a complicated rada construction in order to anticipate the rise and fall motion must be designed to allow the front wheels can be deflected. That is why, the front axle is always equipped with a special connection commonly known as a kind velocity joint or joint cross the plural is used in rear-wheel drive car.
    At the connection point is often problematic. For example, a rubber boot axle broke. If, allowed to continue, then the dust, sand, or other debris will enter into a ball of steel connections is quite expensive. Of course, the steel ball is guaranteed not broken the tempo for a while. Because of that, immediately replace the rubber axle boot was torn know if it is leaking. Try, first check on your car


  • READ MORE.......





  • for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com



  • 7:52:00 AM

    Historical perspective and evolving materials technology

    The progess made in the development of engineering structures over the last century has been dealt with expertly elsewhere2 and with regard to recent model programmes the significant use and benefits of FEM techniques (basic introduction summarized below) in shortening delivery times is emphatic.
    However, as these become more complex, the more need there is for input detail such as material properties. As well as physical properties the need also exists for empirical data regarding material behaviour in diverse engineering situations and it is important that past designs and associated materials performance is analysed and ‘rules’ extracted for future design purposes and use in numerical form when required. In general terms the same developments have been evident on a worldwide scale, although size is a feature of American built vehicles, and the needs of mass production technology, reaching global proportions, have perhaps influenced the Japanese design philosophy (robot access, automation). Therefore although written from a UK perspective, with its foreign ‘transplant’ influences over the years the following content probably mirrors the worldwide trends and requirements for body materials in the future


  • READ MORE.......


  • Materials for Automobile Bodies
    Geoff Davies F.I.M., M.Sc. (Oxon)
    Butterworth-Heinemann
    An imprint of Elsevier
    Linacre House, Jordan Hill, Oxford OX2 8DP
    200 Wheeler Road, Burlington MA 01803


    for more details and updates about automotive-technology-guide please visit.........
    www.automotive-technology-guide.com

    ---or---

  • www.automotive-technology-guide.com


  • 5:13:00 AM

    Automotive technology

    Automotive

    Labels

    1904 Columbus 1940 Ford 1964 Worlds Fair 1969 Camaro 1969 Dodge Coronet Super Bee 2014 2016 Sales 2017 The Bad 8 2017 The Good 12 3 wheeler 4 G 407 407 ex2 427 AC Cobra 440 six pack 442 4x 4x4 55 Chevy 57 Chevy 5th wheel AAR abandoned abs abuse by law enforcement AC Cobra Acadian accessories accident Acoustic processing Active noise control (ANC) Acura Acura Reviews adaptive cruise control ADAS Adobe AIR ads adventurers advertising aerodynamics Aircraft engines airlines airplane Airstream Alfa Alfa Romeo Alfa-Romeo All Cars Rankings All SUV Rankings All Vehicle Rankings Alpina Alpine AMBR winner ambulance AMC America's greatest photographers American LaFrance amphib AMX AMX-3 Andorra Andrew Poliak Android Andy Gryc anti lock braking system App World Apps Arab-Supercar area controller Ariel-Nomad ARM-based devices art Art Arfons Art Deco artist Asset management system Aston Martin Aston-Martin atv auction Audi Audi Reviews audio Augmented reality Austin Austin Healey Australia Austria Auto Accident Attorney auto car donate auto car donation Auto Donate Auto Donation California Auto hobby books Auto Sales By Brand auto show Auto Story in Pictures Wednesday auto taxi Autocar automobile automobile donation AUTOMOBILE INSURANCE automobile parts automobile safety system automobule donate Autonomous cars Awards awesome B 29 B 52 BAIC Baja racing Baker banners barn find barn finds barnfind barnfinds Barracuda Barris barum BatBerry Batman Batteries battery beautiful engine Beautiful paint before and after Belgium Bello's belly tanker Bentley Best Sellers Best Selling American Cars Best Selling Cars Best Selling Luxury Best Selling SUVs Best Selling Trucks Best Selling Vehicles bicycle bicycles Big 3 Swap Meet big wheel bike messengers bike rack biofuel biography BlackBerry BlackBerry Radar BlackBerry-QNX blink code blink code checkup blink code error blink code troubleshooting Blog blogs BMW BMW Audi Mercedes Benz Daimler jeep GM toyota Chrysler VW volkswagon nissan infiniti ford unique rare Bntley boardtrack Boats boattail Bonneville book review bookmobile Boss 302 Boss 429 brake brakes braking system Brand Marketshare brass era breedlove Brewster Brian Salisbury Bricklin bridge British Britten brochure Bugatti Buick Bulgaria burnout bus Buses buying selling cash tips money advice BYD c C-type Jag Cadillac Cadillac Reviews Camaro Can Am Canada Canada 2016 Sales Canada All Cars Rankings Canada All SUV Rankings Canada All Vehicle Rankings Canada Auto Sales Canada Auto Sales By Brand Canada Best Sellers Canada Compact Car Sales Canada December 2016 Canada Entry Luxury Car Sales Canada February 2017 Canada January 2017 Canada Large Car Sales Canada Large Luxury Car Sales Canada Large Luxury SUV Sales Canada Large SUV Sales Canada March 2017 Canada Midsize Car Sales Canada Midsize Luxury Car Sales Canada Midsize Luxury SUV Sales Canada Midsize SUV Sales Canada Minivan Sales Canada November 2016 Canada October 2016 Canada Premium Sporty Car Sales Canada September 2016 Canada Small Luxury SUV Sales Canada Small SUV Sales Canada Sporty Car Sales Canada Truck Sales Canada Van Sales Canada Worst Sellers car care car chase scene car clubs car collections car collectors Car Donate car donate california car donation Car Donations California Car or the Future car wash carbs carrozzeria cart caterpillar tracked vehicle CCS celebrities celebrity Certicom CES CESA 2012 CESA 3.0 Chademo Challenger Chaparral Charger Charity Charity auction charity car donation Charity Car Donation Program Charity Car With Your Credit Card cheating Checker Chery Chevelle Chevrolet Chevrolet Reviews Chevy 2 China chopper Christian Sobottka Christie Christmas Chrysler Citroen Citroën classics cleaning clip Cloud connectivity CO2 Cobra Cobra Daytona Coupe Cobra Mustang Cobra Torino COE Cogent collection collector College Colombia commercial common rail direct injection Compact Car Sales companies comparison compliment components components of anti-lock braking system concept Concept car Concept team Connected Car construction Consumer Electronics Show consumers Contest convertible Coronet Corvair corvette Corvettes Costa Rica coupe coventry cragar crash crde crdi Croatia Crosley crossover Cruise 4 Kids crypto cryptography CTS Cuda Cunningham Curtiss Aerocar Custom customer satisfaction cutaway display cycle car Cyclone Cyprus Czech Republic dacia Daihatsu Dan Gurney dart Datsun Daytona ddis DDS dealers Dealership Dean Martin December 2016 Degree delivery truck Delorean Delphi Demon Denmark Derek Kuhn design deuce devices Dick Landy dicor Digital instrument clusters digital spark ignition Diner with car theme direction injection Disney display diy Dodge domain controller Donate Donate A Car Tax Deduction Donate Automobile To Charity Donate Car To Charity Tax Deduction Donate Vehicles To Charity donation donation auto car donation vehicles to charity Doug Newcomb Drag racing drag strip Dragonsnake dragsters DREAM drifting Driven Driver distraction driving assistance drunk driver DS dtsi dual carbs dual engined dualie Ducati dump truck dvla E-type Jag ECC economy ECU Ecuador electric electric car Electric cars electromagnetic brake Elliptic Curve Cryptography EMF Emil Dautovic Endurance racing engine engine accessories Engine sound enhancement engines Entry Luxury Car Sales enzo Erskine Essex estate Estonia etc EUCAR Europe EV Business Case Evel Knievel event experience experiment extreme sports video F1 Factor-Aurelio Factory lightweight Factory race car Fairlane Falcon Fast boot Fast-Charging FCA FCEV February 2017 Ferrari Fiat Fiat Botafogo finance Finland fips fire engine fire fighting fire trucks Firebird Firestone firetrucks Fisker flamejob fleet management Ford ford escort Ford Reviews Fordson tractor Forecasts FOTA found around the neighborhood France Franklin Free Car Donation Freescale french fuel fuel injection fuel injection system Fuel Tanker fuel-cell fun Funny car Futurliner gadgets Galpin Ford game garage garner gas mileage gas stations Gasser Gauges GCBC Awards GCBC Most Popular Geely Gene Winfield General Motors German Germany give your car to charity GM GM MyLink GNX Go cart good news Goodwood Goodyear gourmet food vans GPU Graham Gran Prix Grand National Roadster Show 2017 Grand Sport Corvette Graph Great Wall Motors Greece green Green car Gremlin GT GT 350 GT 40 GT 500 gt40 GTO GTX Gulf race car Gullwing Guy Martin Hands-free systems Harley Harley Davidson hauler Hawaii helicopter hemi hemmings Hennessey Henry J hero Hertz hire Hispano-Suiza historical history HMIs Holden Hollywood Holman Moody Honda Honda Reviews Honda Sales Hong Kong Hood ornaments hood scoops Horizon 2020 horse carriage horse wagon host blog info about auto Hot rods Hot Wheels Housekeeping How To Donate How To Donate A Car For Tax Deduction How To Donate Car To Charity how to donation car to charity HRM HTML5 Hudson Hummer humor humour Humvee Hungary Hupmobile Hurst Hurst SC Rambler hybrid Hybrid cars hydrogen hypervisor Hyundai Hyundai Reviews Ian Roussel Iceland ID4 Car ignition IIoT immitation Impala india Indian Indianapolis industry news infiniti Infiniti Reviews Info infographic informative Infotainment Injury Lawyer Innotrans innova innovation innovative instrument panel insurance intake Intel interior International Harvester Internet of Things Internet radio invitation IoT Ireland iris iris details iris engine details iris technical Isetta Iskenderian Isky Isle of Man ISO 26262 Israel issues Isuzu Italian Italy ITS ITU IVI Jaguar January 2017 Japan Japanese Javelin Jay Leno Jean-François Tarabbia Jeep Jeep Wrangler JLR John D'Agostino John Deere John Wall Justin Moon jv Kaivan Karimi Kandi kawasaki Ken Block Kerry Johnson Kia kids Kim Cairns Kissel Kombi Kroy Zeviar Kurtis La Carrera Panamerica lace paint Lamborghini Lamborghini Revuelto Lancia Land Cruiser Land Rover Land Rover Sales land speed record holder Land-Rover Large Car Sales Large Luxury Car Sales Large Luxury SUV Sales Large SUV Sales Larry Wood LaSalle Latvia launch law enforcement lawnmower laws Le Mans legends Leno Lexus license plates Lidar Life Insurance limited Lincoln Lincoln MKZ Linda Campbell Linda Vaughn links lists Lithuania live Loans Locomobile logging train logging trucks Lola London to Brighton Looking for EV's Los Angeles Lotus lowrider LSR Luxembourg luxury Lyft Lynn Gayowski Mach 1 machine shop Mack Mad Max magazine magazines magic iris mags Malaysia March 2017 Mario Andretti Mark Donohue marketing Marketshare Maserati Matt Watson Maverick Mazda Mazda Reviews MB McLaren mechanic Megan Alink meme Memory Lane Men Micro Mercedes Mercedes Benz Mercedes-Benz Mercer Cobra Mercury Metallica Metro Mexico Miata microkernal Midsize Car Sales Midsize Luxury Car Sales Midsize Luxury SUV Sales Midsize SUV Sales Military Miller race car mini mini bike miniature Minivan Sales MirrorLink mission-critical Mitsubishi Miura MMI Mobile connectivity Mobile World Congress mod top Model Model A model T modifications Momo Monaco Monster Truck Moon Moon eyes Mopar Mopar parts Morgan Morocco morons mot Motor shows motor wheel Motorcycle Motorcycles motorhomes Mouse movie movies mpv Multicore Munsters Muntz muscle cars musclecars museum music video Mustang NAIAS Nancy Young Nascar Nash Navigation naza neglec neglected Netherlands new tv show New York New Zealand news ni Nissan Nissan Reviews Nomad Norway nos nose art Nova November 2016 Nurburgring Object Management group October 2016 off roading offenhauser Oldsmobile OMG Online College OnStar Opel Open source Open standards OpenGL ES option orders original owner Ormond Beach land speed racing pace car Packard Pagani Paige pamphlet panel paint Paris to Peking race parking parts Patryk Fournier Paul Leroux Paul Newman Paul Sykes Pebble Beach pedal car perodua personal Peter McCarthy petrol petroliana Peugeot Phoenix Injury photographer photography pics pictures Pierce Arrow Pike's Peak Pinin Farina pinstriping Pit row Pits Pixar PKI plank road PlayBook Plymouth Point Grey Camera Poland pole wheel police Polysynch Pontiac Porsche Porsche 917 Porsche Carrera Portugal POSIX pre 1930's gas station Premium Sporty Car Sales President of the USA Preview prices prius project prooject Proton prototype PSA Peugeot Citroen public key cryptography Pullman QNX QNX CAR QNX Garage QNX OS Qualcomm quiz quote race cars racing racing. LSR Radar radio Raid Data rail railcars railroad ralliart Rally rallying Ram range rover rant Rapid Transit System advertsing rare Real time Innovations recall recommended shop record setter Red Bull Sports Reference vehicle Reliability Rémi Bastien RemoteLink Renault Renesas Renntransporter rentals REO repair reports resarch research restoration restoration shop review Richard Bishop Ridler Award Winner rims river bank cars road and highway Road Runner roadster Robot OS Robot wars Roewe Roger Penske Rolls Royce Romain Saha Romania ROS Roth RTI RTI Connext rumble seat Russia Ruxton RV Safety Safety systems safety-certified sales Sales By Model Sales Stats samba sampan Saoutchik Satellite satnav Scaglietti scallops Scat Pack SCCA racecar School bus sci-fi Scooter SCORE Baja trucks Scott Pennock Scout sculpture Security sedan segway semi sensor extension cable sensor fusion September 2016 service service repair automotive vehicle car buying selling mission statement blog free broker shay drive locomotive Shelby shifter shop Show cars sidecars signs skateboarding Skoda slicks slingshot dragster Slovakia Slovenia Small Luxury SUV Sales Small SUV Sales Smart Smartphones snow machines snowmobile Soapbox South Africa South Korea Sox and Martin Spain spare tire spark ignition spark plug spark plugs Spatial auditory displays special edition Mustangs Speech interfaces speed limit Speed Record speedfest speedster sports car sports cars Sporty Car Sales spy shots spyker Sri Lanka SS SS/AH Stagecoach Stanley Station Wagon steam locomotive steam powered steam shovel steampunk steering wheel Steve McQueen Stig Stirling Moss Stolen streamliner street cars Street Van studebaker stunt stunts Stutz Stutz Blackhawk Subaru Sunbeam Super Bee Super Stock Superbird Supercar supercharger survey suv Suzuki Sweden Swift Switzerland System development Life Cycle Tablets Tach takeover tank tata tata magic iris tata vehicles tax Tax Deduction For Car Donation taxi taxi cab TCS tdi teardrop technical technology Telematics Telematics Detroit Telematics Update tempo Tempo Matador Terlingua Racing Team Terry Staycer Tesla test testdrive Texas Instruments The Race Of Gentlemen Thomas Bloor thoughts three wheeler Thunderbird ticket Tiger Tim Neil Tina Jeffrey tips tires tool tool kit toolbox tools Top Gear top ten list Torino tour bus tourbus towtruck Toyota Toyota Entune Toyota Reviews tractor trailer train train wreck trains Trans Am transmission Transporter Traval trike Triumph trivia trolley Troy Trepanier truck Truck Sales trucking trucks Tucker turbocharger turbojet turbonique Turkey tv tv cars twin spark type 1 type 2 tyres UAE Uber UK UK Auto Sales UK Best Sellers uk market Ukraine Unimog unique University of Waterloo Unser unusual unveil upgrade US US 2016 Sales US All Cars Rankings US All SUV Rankings US All Vehicle Rankings US Auto Sales US Auto Sales By Brand US Best Sellers US Compact Car Sales US December 2016 US Entry Luxury Car Sales US February 2017 US January 2017 US Large Car Sales US Large Luxury Car Sales US Large Luxury SUV Sales US Large SUV Sales US March 2017 US Midsize Car Sales US Midsize Luxury Car Sales US Midsize Luxury SUV Sales US Midsize SUV Sales US Minivan Sales US Navy US November 2016 US October 2016 US September 2016 US Small Luxury SUV Sales US Small SUV Sales US Sporty Car Sales US Truck Sales US US Auto Sales US Van Sales US Worst Sellers USA used cars V2X van Van Sales vauxhall VeDeCoM Vehicle Donation California Velodyne Vespa Video vintage vintage racing Virtual mechanic Virtualization VOIP Guide Volkswagen Volkswagen Reviews Volkswagen Sales Volvo Von Dutch vote VW VW bug W3C wagon train wall of death washer washer fluid Watson's Webinars website what is donation what is it wheel speed sensor wheelchair White williams Willys windshield washer wing Wireless framework women woodlight headlights Woody work truck working principle of anti-lock braking system workshop World Worst Sellers wreck Wrongful Death WW1 WW2 XK SS Yoram Berholtz Yoshiki Chubachi Z 11 Z-28 Z28 zamboni ZL1 Zotye